commadore

After repairing a fuse problem I had with infotainment I now realise half the problem was the fascia. When I take the fascia off and resit it my radio will work for a couple minutes before cutting in and out. Is there a way to repair this poor connection or is it looking like a replacement...

Hey guys, a little while ago I put a l67 into my vy Ute. All is going well but it seems to have a lump on idle like theres a vacuum leak somewhere. I noticed under the throttle body there was a vacuum hose that was open. So I blocked it up with a screw and the idle went smooth. But when I went...

Let the kangaroos hop, the koalas snooze, and the BBQs sizzle! Today, we're not just celebrating a day; we're celebrating the spirit of this sun-kissed land we call home! Let's accelerate the joy and unity this Australia Day! Cheers to the red, white, and blue – and the roaring engines too...

I have a svz svz ute that I just bought with a blown motor I put a new engine in it and my key is not cranking the engine at all I can start it by the relay by then I get powertrain codes come up abs step performance stuff like that my key unlocks and locks the car but not starting

Hey guys, Replacing my ecu since it’s gone haywire, won’t read through the obd2 scanner, keeps causing misfires and trans shifting issues but goes away when reset then comes back. I’ve read I need a tech2 to pair the ecu and bcm together, will any other scan tool work? Or is there anyway...

This Christmas and New Year, give your ride the gift of performance and reliability! Use Promo Code MACE2023 for exclusive deals: Enjoy a massive 10% OFF on all products at our AU and NZ websites! www.maceengineering.com.au �� www.maceengineering.co.nz Get 5% OFF on our eBay Store! Perfect for...

I’ve just bought a VU commodore that’s not starting, it’s had an engine swap and apparently was running after the engine swap but then died, the previous owner did lots while troubleshooting including linking a new ecu to the bcm because it wasn’t cranking. It now cranks and the fuel pump...

Hey guys, I have recently rebuilt and installed a new 3.8l ecotec into my 2002 vx commy. Has all new gaskets, timing chain, piston rings ect. Motor will start okay but Idols and runs really rough. The motor seems very shaky and unusually quiet. I have tried changing leads, plugs, sensors...

hey guys I really need some as I’m lost? I’ve taken a vs motor and manual box out of a 4 door vs and put into a vs Ute? Everything plugged up but just won’t start has red but just can’t figure out why it won’t start. I’ve tried changing bcm and key and still nothing. Would anyone know what why...

Hey Guys, Just wondering if anyone could give me some help with my clutch. I recently have just had the motor rebuild. I put the motor back in with a new heavy duty clutch, flywheel and slave cylinder in. The sound only occurs when I am taking off. So when I press down the clutch no sound. It’s...

Hey so I’m looking at lowering the rear my VU 2002, I got 20” rims on. I got some people saying to go sl as id need my guards rolled for ssl. But others saying to not bother with sl cause it won’t really do anything and ssl will be fine. Any thoughts ?

Just see if anyone put mace performance cam616 210/210 0.050 in a crewman s V6 stock alloytec LE0 engine

I was putting a boost gauge in my vx L67 i was putting the hose on the nipple but it snapped the nipple what do i do?

Hey Guys been searching around the web for ways to get my 2014 vf to work with android auto but most of the solutions are around the $1k mark and many are a lot over that amount , is their any diy solutions that are a bit cheaper in order to get apple car play and android auto integration working???

I have a 2008 Caprice and am wondering why when a passenger is seated and their seatbelt isn't on the alarm doesn't sound. If the driver doesn't wear the seatbelt the dash beeps and shows a symbol on the screen and light on the cluster not sure if my car has a defect with the passenger system or...

Stato (99' WH) is being a ****, won't turnover even though I started it literally yesterday, all the lights on the inside are coming on (but turn off when I turn the key to actually start not just accessories) but it will not turn over thinking it may be a fuse or the starter motor, thought it...

Hi all, So bare with me and I'll try explain everything this is my first post and I appreciate any help I can get. My VZ Calais has been sitting for 10 months and I've had the battery disconnected. I'd Start it now and again and everything was fine. The other day I started as usual and moved...

Hey fellas/lasses just needing some advice about my car/engine (WH statesman, N/A 3.8 V6.. pretty sure an L67) I was talking to one of my mates earlier today about cars and then I bought up my car and what I want to do with it, I told him the car and engine she has in her and that later on down...

Hey Guys! I just got my first car it is a 1998 VT commodore executive and the body isn’t perfect it needs some touch up paint which is no biggie however something that is really getting to me is the front and rear bumpers have massive bumper gap and I am writing this post to ask for help on as...

Hi there, Just wondering if anyone knows or has had any issues with a Holden omega 2008 model. The radio comes up with mechanism error, the aux cord doesn’t work (once in a blue moon it’ll decide to work) And now the radio/ display screen has started to stop working every now and again. Does...

Hi all, I have a vy calais and recently my passenger side mirror started playing up. When I press one of my presets on my seat, the side mirror won't go into the right position and will just tilt all the way up (facing the sky) or even when I go into reverse the mirror won't tilt to the lower...

Hi all, I have a vy calais and recently my passenger side mirror started playing up. When I press one of my presets on my seat, the side mirror won't go into the right position and will just tilt all the way up (facing the sky) or even when I go into reverse the mirror won't tilt to to the lower...

Hey guys, just looking for some advice on upgrading cam on my VF Ute. It’s currently running a W457 package, mantic 9000 and true trac. It’s not a daily drive anymore so I’m not afraid to open her up a little. Anyone Else done something similar that could share me some insight would be great...

Hey guys, I know this is a stupid question but I just bought a VX and wanted to know how to put the Calias boot garnish on. And where to buy it. Do I need a new boot? Does it just screw on?

Just signed up guys hoping someone may be able to help in any way... Will a 3.6 L Alloytec from a VE work in a VZ..not changing the computers only the motor.. Different mounts and sump I beleive..will that stop it from being possible? Does anyone know if it will work and why if it doesnt? Ide...

Hi all just a quick Question is it possible to disable the auto dimming feature on a VF series 2 sv6?, example certain light sources cause the infotainment display to dim this is especially annoying when I'm using the reversing camera. any tips or help would be great! Cheers :)

Hi I am just wondering if someone can tell me what’s the easiest and Simplest way To remove and replace the engine mounts on my 2006 Holden Commodore Omega

Hey guys recently had a noise with my 2002 vx commodore coming from breaks area so I changed them to bendix brake pads but since then whenever the car heats up the breaks squeal really loud and got no idea why help please

Hey guys anyone know how to get the ve hard lid light working I bought the lid second hand and they didn’t have a wiring harness and I figured if I can do it without buying the harness would be cool, I’ve got the central locking all connected up but I’m unsure of what wired connects to the...

Wanting to buy a diff it’s just gonna get welded up but I’ve got a vy 3.8 and was wondering what models can I buy a diff out of and it will bolt straight up not. Don’t know much about cars so just looking for tips and advice

Hey all I have a custom exhaust made for a vz Ute I’m also looking to buy a vs siii statesman I know statesman’s are long wheelbase but are they compatible with that gen of exhaust Looks to be a very similar shape at a glance

This is the story. Went to shop and buy a spark plug of 6 (NGK BPR6EFS-15) for Holden Commodore VY V6 2003 series II. Not because old spark plug are bad. Just want to change to a new set. Drive back home. Put the new spark plug in and in all of them. Car on "Wish me a Luck". It make a surge...

This is the story. Went to shop and buy a spark plug of 6 (NGK BPR6EFS-15) for Holden Commodore VY V6 2003 series II. Not because old spark plug are bad. Just want to change to a new set. Drive back home. Put the new spark plug in and in all of them. Car on "Wish me a Luck". It make a surge...

Need advice with vr 90ish commodore engine, Replaced air intake with 4inch re routed pod fliter, No exhaust mods, Dose this cause the engine to idle at 2000rpm even when hot, needs tuning? Throttle cable seems fine, and throttle body appers to be working fine, I work on trucks and excavators...

Hey guys, YES another VE timing chain thread! LOL I have a 2011 VE sv6 with a rooted timing chain. My only question is any recommended kits? I’ve seen a bunch of cheap ones on eBay but a little weary of them - And been quoted about $1200 from Holden ( excluding labour ) Don’t mind paying the...

Who has frosted tail lights on a vn vp vs vr wagon? Just want to see some other wagon bootys for inspiration.

Doing spark plugs and everythings in the way of cyl 6, what can i move and what dont i move Vr buick 3.8l

I went to change my old Tyre to news. But later when I pick up and went to servo for pressure checking. Because it look bad, if Tyre look alright. I wouldn't check the pressure. the 3 Tyre was nearly fk the rim. And one seem to be in good psi. Then put a hose in. Wow, don't know what happen...

hey all, New to this so please no hate, only a young fella trying to figure something out. I have recently done a compression test on my 2000 VX Commodore with the L67 in it. The motor has approx 250 thousand k’s on it. Just curious as to what the readings should be. The readings I got were...

Hey guys I just purchased some headers (1 3/4) for my VE 6.0, which should bolt directly on to my 2.5" xforce catback system. Was wondering if anyone knew of a decent workshop/mechanic who installs aftermarket parts for a reasonable price and quality. Located in Western Sydney, cheers.