Search results

sounds like a beast man. i put blue tops in better up top little laggy down low to rich. i ran to mafs piggy backed the loom and it ran bad and wouldnt rev over 3000 wondering if i could put a resistor in to half the voltage? the reason being i want 1 maf and 1 trottle body and put another...

injectors on their way, vn throttle bods nearly ready let u guys know how that goes. after a a week or so it seems to be getting better more responsive and economy is ok on average 13.9-100k not bad for around town giving it a little bit

thanks mate im in the middle of putting 2 vn 60mm on ive cut the iac off and plugged the holes with metel mend. in theory vn ones are smaller and would make it more pokey off the mark and more driveable instead of giving it a gut full of air and a headache. i could only imagine what 2 70mm from...

ill go down to the local speed shop and might get an adjustable reg. rising reg is prolly over board for me

yeah maybe when i put the mani on i tapped the injectors upside down and a bit of silt come out of them so need a change or a clean anyway. and whats a cheap fuel reg that would suit this type of aplication. i dont think the ecu can handle itself 2 well. need the iac tweaked for idle it really...

yeah it has a lot more poke off the mark and heaps off pull a 3000 and dies off a bit at after 5000 and the engine light comes on with Code 57 - Injector Power supply voltage variation. i dont think im getting enough fuel up top i got bluetops coming and im making a plenum spacer so ill get...

yeah it goes better i got some bluetop injectors coming but not sure about the empediance compatability dont know much about that stuff. wouldnt mine some snails but cost a bit. i might go a ls1 maf for more flow and a bigger flange on the airbox. hope i get around 200rwkw and down the track i...

cheers mate doing it on the cheap lol just want to get it all going well before i get welds touched up and the grinding finished in case its not worth it. but i tell u 1200 for one from mace people would be unhappy for the hp gains for money value. mine still cost less than my k+n filter so i...

bed fame for y peice 3' just about as thick as zorst pipe but cost nothing. having troubles with idle but pretty sure its the second iac but goes well

thanks guys ill touch up a few spots and clean up again. with the tune yeah its needs one i have just done the y pipe to plumb the maf and runs heaps better idles @ 1100 tho because one of the iac's need to be reset in its closed position but i will cut that off a throttle body and weld the...

cant get them up here but got them on my profile how do u get them up here?

[IMG]http://forums.justcommodores.com.au/members/dan202-albums-v6-twin-throttles-picture109847-dsc00852.JPG

ok i have a mild cam roller rockers acl race series pistons shaved heads match ported inlet manifold pacemaker extractors twin hi flow cats 2.5' exhaust otr cai k+n panel filter. ill get some pics up tomoz

hey all i have made a twin throttle mani on my vr with a vx ecotec engine and thought id share my experience with u guys. first of all it does run without a maf or piping but u have to slot the tps bolt holes and turn it clockwise it runs better then. and i am running stock injectors atm even...

fixed the earth cable put another battery in 13.8 - 14.1 car running and full load lights heater a litttle bit better power but not the same as it went the other day

after i tightened the terminal it started fine and reved a little high and dropped pretty quick back to idle, and as for the battery after jump startig it may have boosted a bit more charge maybe? ill have a look today and check connections and battery condition and beef up the earth to the body...

theres not much more i can think of that will cause a problem i have no engine light but that doesnt mean much it is booked in at holden to get put on their computer gear and take it from there if something needs to be replaced ill do that and i got quoted 800 for dyno tune sounds cheap u get...

na no tune yet i thought i may of had a bad earth somewhere or something and it got a good connection for a bit dunno? just a one off i think?

i had the same problem been stumped for months, car drove fine idled fine but stalled when coming to a stop and light came on looked at the ecu loom and a wire was out turns out the purple white wire for speed sensor put it pin d2 thought bingo, still no go the wire was broken 6 inches up the...

hey all have worked vx engine and t5 in a vr with full vs statesman boby loom and vs t5 engine loom and ecu, it runs really well, but the other day i jump started my other car and all was fine turned it off left for a bit and got in it later and started it but the terminal was loose and lost...

hi where do u get these nvram boards? i have aldl cable to usb i bought from ebay so i just get the nvram and download super tuner pro and im away yeah?

why not just put a v6 into an older commy me and my mate done a v6 vl for a bush bomb and its still better than yours wish we had your extractors would of been " fully sick "

the car was built by hp heaven im positive it is ballanced but there should dowels to locate the flywheel the engine has no vibrations when in gear or neutral flywheels bolts shouldnt have any force on them when all 8 bolts are in just nipped up the flywheel still turns to the left and right 3...

heres a funny story i put my engine and box in and had a mate help me went in all good and ran well but when u floored it it vibrated the doors of it it turned out to be the little banana cross member was put on backwards and the balance weight that comes off the gearbox was hitting on it under...

yeah ive used loctite new bolts already have blue loctite on them already but i put more on, the gearbox and flywheel where out of an earlier car like vn or vr but there is some 3/4 inch holes drilled in the flywheel so i beleive its balanced, ive never seen them in a vr flywheel before and the...

yeah an adayer lexen

well put new bolts in again and ***ed again this time im putting a lightened flywheel and 2 5mm dowel pins in and if this fails the peice of sh!t is going to scrap and going to buy a ef xr6

this guy is so brain dead or he is having us on but the celica would go hard with the backyard bodge extractor and 15kw pod in the oil filler power to weight should be good but might need op slotted rotors

yeah the engine loom is genuine and not played with and the purple/white wire is in d2

omfg this is hilarious im sorry man to laugh at your exspense but im sitting here with some mates and were rolling on the floor crying. 10 pionts for trying but i feel so sorry for u

hey all i have a t5 behind a vx ecotec in a vr with full vs stato body loom and a vs t5 loom and ecu and the speedo works on the dash but the ecu side of things doesnt, fault code 94, i havnt used the statesman steering rack for the solenoid would that be part of the problem? should i try a jump...

found out it goes in d2 but still got code 94

hey all i have a vx ecotec in a vr with a t5 and the flywheel has come loose twice now i have used new genuine bolts both times and torqued them up properly the engine is worked, because the motor was auto i was wondering if they had a dowel pin in manuals? or what can i do to prevent this from...

the chip is matching numbers to the ecu o its one or the other im going to try a jumper lead to the ecu d2 pin to the purple/white wire on the speed sensor but my guess is its a getrag ecu but why did the ecu say auto or man it should say getrag or t5 to save all of us the confusion

i bought a loom of ebay with the same 3 wire plug and it went on the screw in sensor and i have a manual ecu not sure weather its a t5 or getrag ecu but the speedo works on the dash but i have a 94 fault code not sure why but it stalls when coming to a stop but when i done my conversion i used a...

hey all i have a vss fault when i come to a stop changing back to first and its stalls i changed the speed sensor and still the same there is a wire out of its socket in the computer it was like this when i done my manual conversion its a t5 box vs series 1 loom and t5 ecu the wire is purple...

cool as 3.50 sounds good but ill use him as a last resort ive contacted bob so hope all goes good plus a worked motor of stock chip is usless

i only need the chip coz he said he needs a blank or a aftermarket on he said he cant overwrite a factory1 checkin out the link now cheers